The short answer
A tube mill is a production line that forms flat steel strip into a round tube, welds the seam and cuts the tube to length. On an ERW tube mill the seam is welded with high-frequency current. "Pipe mill" is used for the same kind of line when it makes pipe: fluid pipe ordered by nominal size and wall schedule, such as NPS 2 Schedule 40, and made to pipe standards such as ASTM A53 or API 5L.
For ERW lines, tube mill and pipe mill are largely two names for the same machine. The forming, welding and sizing work the same way. What differs is the size and wall range the line must cover, the standard the product must meet, and the finishing and testing at the end of the line. One line can make both pipe and tube, including square and rectangular tube.
"Pipe mill" can also mean a plant that makes seamless pipe from solid billets, or submerged-arc welded pipe from plate or wide coil. Those work in a completely different way from an ERW tube mill.
What is a tube mill?
A tube mill, also called a tubing mill or tube making machine, turns coiled steel strip into welded tube in one continuous line. An ERW tube mill line has five sections:
- Entry: uncoiler, leveler, shear & butt welder and spiral accumulator, which keep strip feeding while coils are changed
- Forming and welding: roller stands bend the strip into an open round tube, and HF welding joins the edges
- Cooling, sizing and straightening: the tube is cooled, sized to its final diameter and straightened; square and rectangular tubes are shaped here
- Cut-off and run-out: a flying saw or cold saw cuts the moving tube to length
- Optional finishing: end facing, testing, stacking and bundling
Each stage is described in our guide ERW Pipe Making Process: From Steel Coil to Finished Tube, and the welding step in High-Frequency Welding in ERW Tube Mills Explained. A "steel tube mill" is the same machine; the name only stresses the material. "Tube forming machine" is sometimes used for the whole line, but strictly it means the forming and sizing mill at its center.
What "pipe mill" can mean
Buyers and suppliers use "pipe mill" for at least three different kinds of plant:
- ERW pipe mill: an ERW tube mill that makes pipe. It works exactly like the tube mill above.
- Submerged-arc welded (SAW) pipe mill: welds with filler wire under a layer of flux. Longitudinal (LSAW) mills form plate and make a straight seam; spiral (SSAW) mills form coil into a helix and make a spiral seam. They make mainly larger diameters and heavier walls than ERW.
- Seamless pipe mill: pierces a heated solid billet and rolls it into a hollow, so the pipe has no weld at all.
So when a quotation or a search result says "pipe mill", check which process it means. The products themselves are compared in our guide What Is ERW Pipe? ERW vs Seamless, Uses and Sizes. InGen MillTek builds ERW tube mill lines; we do not supply seamless or SAW pipe equipment.
Tube mill vs pipe mill at a glance (ERW lines)
- What they make: a tube mill typically makes tube for structures, machinery, furniture and automotive parts, in round, square and rectangular shapes. A pipe mill typically makes round pipe for water, gas, oil and fire sprinkler lines, and line pipe.
- How the product is ordered: tube by its actual outside diameter (or side lengths) and wall thickness; pipe by nominal size and schedule. NPS 2 Schedule 40, for example, is 60.3 × 3.91 mm.
- Typical standards: for tube, ASTM A500 and EN 10219; for pipe, ASTM A53, API 5L, EN 10217 and GB/T 3091.
- End of the line: tube lines focus on cut length, cut quality, stacking and bundling. Pipe lines more often add end facing and chamfering, hydrostatic testing and eddy current testing, and, for galvanized pipe made from pre-galvanized strip, an in-line zinc repair unit for the weld seam.
- The mill itself: the same forming, HF welding and sizing principle. The model is chosen from the largest outside diameter and the heaviest wall the line must make, so pipe sold by schedule can call for a heavier mill than tube of the same diameter (see the next section).
Why pipe schedules can call for a bigger mill
Outside diameter alone does not decide the mill; the wall thickness often does. Take NPS 2 Schedule 40, which is 60.3 × 3.91 mm. By outside diameter it falls within four of our models: YJ-50 (Φ19.1–63.5 mm), YJ-76 (Φ38.1–89 mm), YJ-89 (Φ50–102 mm) and YJ-102 (Φ50–114 mm). By wall thickness, YJ-50 goes up to 3.0 mm and YJ-76 up to 3.5 mm, so the smallest model that covers both is YJ-89, with walls up to 4.0 mm. A plant making only 60.3 mm tube with a 2 mm wall could use a smaller mill.
The rule is the same for tube and pipe: choose the smallest model that covers your largest outside diameter and your heaviest wall together, checked for your material. The full method is in our guide 10 Steps to Specify an ERW Tube Mill: Tube Size to Full Line.
From small tube mills to large-diameter pipe mills
Tube mills are built in size classes. InGen MillTek's 12 YJ models cover round tube from Φ10–25.4 mm on the YJ-20 up to Φ140–273 mm on the YJ-273, with walls from 0.4 to 10 mm. By outside diameter, that spans pipe sizes from NPS 1/8 (10.3 mm) up to about NPS 10 (273 mm). The same models make square and rectangular tube. Beyond these 12 common models, larger mills are designed and built to order, up to 400 × 400 mm square and about Φ510 mm round.
Line speed falls as size rises: up to 120 m/min on the YJ-32 and up to 30 m/min on the YJ-273. The YJ-219, YJ-254 and YJ-273 are large-diameter models designed and built to order. The full table is on our ERW Tube & Pipe Mill Lines page.
Names you will meet, and machines not to confuse
Names for the same kind of line: tube mill, tubing mill, tube making machine, steel tube mill, ERW tube mill, HF tube mill, pipe mill, ERW pipe mill and pipe making machine.
Machines that are not tube mills:
- Roll forming line: bends strip into open profiles, such as C and Z sections, without welding a seam.
- Spiral accumulator: stores strip on an ERW line so the mill keeps running during coil changes. It has nothing to do with a spiral welded pipe mill.
- Slitting line: cuts wide coils into the narrow strip a tube mill needs. It sits before the tube mill, not in it.
Choose by your products, not by the name
Whether a supplier calls its line a tube mill or a pipe mill tells you little. What decides the line is your product list: every outside diameter (or side length) and wall thickness, the material and its strength, the standard and tests the product must pass, the target line speed and how you will cut, test and pack it. Start with that list and follow 10 Steps to Specify an ERW Tube Mill: Tube Size to Full Line.
What InGen MillTek supplies
YinJiang's manufacturing began in 1997. InGen MillTek supplies complete HF ERW tube mill lines for round, square and rectangular tube and pipe: 12 common models from YJ-20 to YJ-273, with forming & sizing units and flying saws, and HF welders, cold saws and automatic stacking configured to suit the project. The entry section is our particular strength: uncoilers, leveling machines, shear & butt welders and spiral accumulators are built in-house, and the spiral accumulator is our flagship product. Larger mills, up to 400 × 400 mm square and about Φ510 mm round, are designed and built to order. Slitting lines to prepare strip for the tube mill are also available.
Every line is configured for your tube sizes, material, coil weight, line speed and local power supply, and prices are quoted for each configuration.
Frequently asked questions
Prepared by the InGen Engineering Team. Values are reference values and are confirmed in the technical proposal and technical agreement.
- Is a tube mill the same as a pipe mill? For ERW lines, mostly yes: both form strip into a round tube and weld it with HF current. "Pipe mill" stresses pipe products, standards and testing, and can also mean seamless or SAW pipe plants, which are different machines.
- What is a steel tube mill? A tube mill that makes steel tube. Most steel tube mills are ERW lines that form strip and weld the seam with high-frequency current.
- What is a tubing mill? Another name for a tube mill.
- What can one tube mill make? Round pipe and tube within its diameter and wall range and, with matching sizing rollers, square and rectangular tube. A square or rectangular tube shares the forming rollers of the round tube with the same perimeter and needs one extra set of sizing rollers.
- Can a tube mill make seamless pipe? No. Seamless pipe is made from solid billets on a seamless pipe mill. Every tube from an ERW tube mill has a welded seam.
- Which tube mill size do I need? The smallest model that covers your largest outside diameter and heaviest wall together. Our 12 common models cover Φ10 to Φ273 mm round tube, and larger mills up to about Φ510 mm are designed and built to order; see 10 Steps to Specify an ERW Tube Mill.
- How much does a tube mill cost? Tube mills are configured for each project and quoted for each configuration. Rollers are quoted separately for the sizes you will make.
About this article
Prepared by the InGen Engineering Team. This is a general technical guide, not a specification or performance guarantee for any project. Model ranges are the catalogue standard series; final parameters are set in the technical proposal and technical agreement.