InGen MillTek YinJiang

Technical guides

How to Specify a Coil Slitting Line: Width to Strips

Eight steps to specify a coil slitting line: material, coil size, slitting patterns, knives, edge trim, recoiling, output and plant layout.

The short answer

You can specify a coil slitting line in eight steps: (1) material grade and strength decide the knives and the slitter's drive; (2) the widest and thickest master coil decides the model; (3) coil weight and coil inside and outside diameter decide the uncoiler and how coils are loaded; (4) your slitting patterns decide the number of strips, the narrowest strip and the knife and spacer sets; (5) the coil edges decide the edge trim and the scrap winder; (6) the slit coils your next machine needs decide the recoiler and unloading; (7) output, pattern changes and line speed together decide how much the line really produces; (8) workshop, cranes and power supply decide the layout.

The core rule: specify the line from your slitting program, meaning every coil and every pattern you plan to run, not from the maximum width alone. Slitting equipment that takes your widest coil can still be wrong for your thickest or strongest material, or for your narrowest strip. For how a slitter works, see our guide What Is a Slitting Line? How a Coil Slitter Works.

Before you start: write your slitting program

A coil slitting line, also called a metal slitting machine, a coil slitter or simply slitting equipment, is configured for the coils it will cut. Before you ask for a proposal, list:

  • Each material: grade, yield and tensile strength, coating (for example galvanized or ZAM)
  • Master coils: width and thickness range, coil weight, inside and outside diameter
  • Each slitting pattern: the strip widths and the number of strips of each width
  • What each strip is for, for example which tube size it feeds
  • How often each pattern runs, and your annual tonnage

Mark which patterns you run every day and which are occasional patterns near the limits. Checking every pattern on this list is far more reliable than comparing the maximum width, thickness and speed of different machines.

Step 1: material and strength → knives and drive

Input: material grade, yield and tensile strength, thickness range and coating. Decision: knife material and settings, and the strength and drive power of the slitter.

Thicker and stronger strip takes more force to shear. The slitter then needs more drive power, stiffer arbors and stands, and knives that suit the material. Galvanized and zinc-aluminium-magnesium (ZAM) coated strip run on the same lines as cold-rolled and hot-rolled carbon steel. Stainless and high-strength steel need suitable knives and settings and are reviewed for each project, so send their grades and strength values with your first inquiry.

Step 2: widest and thickest coil → model and speed

Input: the widest master coil, the thickest strip and the thinnest strip. Decision: the slitting line model and its speed configuration.

The number in each InGen MillTek FT model is its maximum incoming strip width in millimeters, from FT250 to FT1600. Choose the smallest model that takes your widest master coil. Then check thickness:

  • FT250 and FT800 slit strip up to 4 mm thick at 70 m/min.
  • On FT1000, FT1250 and FT1600, the same machine changes speed with thickness: strip up to 4 mm runs at 100 m/min (FT1000, FT1250) or 80 m/min (FT1600), and heavy-gauge strip up to 8 mm at 30 m/min.

So a plant that slits mostly thin strip but sometimes heavy gauge can run both on one FT1000, FT1250 or FT1600 line, at the lower speed for heavy gauge. For strip thicker than 8 mm, or very thin strip, send the details for review.

Step 3: coil weight and size → uncoiler and coil loading

Input: the heaviest master coil, and the coil inside and outside diameter. Decision: the uncoiler type and capacity, and how coils are loaded.

Wide, heavy master coils usually need a single-head hydraulic uncoiler or a double top-cone uncoiler; see our guide Decoiler Types: Choosing an Uncoiler for Steel Coil. Heavy coils are loaded with a coil car, which is optional with the uncoiler. State your heaviest coil and your coil inside diameter, so that the mandrel's expansion range and the coil car can be set. Coil weight and coil diameters are confirmed for each project. For thick or poorly shaped master coils, a pinch-roll and flattening unit can be added at the entry, depending on the project.

Step 4: slitting patterns → strips, knives and spacers

Input: every slitting pattern you plan to run. Decision: the number of knife pairs, the narrowest strip the line must cut, and the knife and spacer sets.

All strips plus the edge trim must fit within the usable coil width. For tube mill strip, each width comes from the tube's outside perimeter: about OD × 3.14 for round tube as a theoretical value, and usually slightly less in practice, because the roller design sets the actual width. See our guide ERW Tube Mill Calculations: Strip Width and Weight per Meter.

Worked example, for illustration only: a plant makes Φ76 mm and Φ50.8 mm round tube from 1,250 mm wide coils. Φ76 tube needs about 239 mm of strip and Φ50.8 tube about 160 mm. One pattern of three 239 mm strips and three 160 mm strips takes 717 + 480 = 1,197 mm, leaving about 53 mm for edge trim, or about 26 mm per side. About 96% of the coil width becomes strip. Before the knives are set, check the widths against the actual roller design and the width tolerance of the incoming coil.

Then check three limits for each pattern:

  • Number of strips: how many strips one pass can make depends on the strip thickness and the slitter configuration. State your largest number of strips and the thickness it goes with.
  • Narrowest strip: a strip that is very narrow for its thickness is harder to cut straight and to wind evenly. State your narrowest strip and its thickness.
  • Knife and spacer sets: spacers between the knives set every strip width. They come in a range of standard widths, and thin shims make up the exact width. The knives and spacers supplied with the line decide which patterns you can set up on day one, so list the patterns you need at start-up; more sets can be ordered later.

Step 5: coil edges → edge trim and scrap winder

Input: the edge condition of your master coils (mill edge or already trimmed) and their width tolerance. Decision: the edge-trim width and the scrap winder.

The two outermost knife pairs usually trim both edges of the coil, so that every slit strip has a clean, defined edge. The wider the width tolerance of your coils, or the rougher their edges, the more trim you need to allow. The trimmed edges are wound up by the scrap winder, which is set up for the trim width and the thickness you will run. Edge trim is lost material, so include it when you compare slitting in-house with buying slit strip.

Step 6: the slit coils you need → recoiler and unloading

Input: what the next machine needs from each slit coil. Decision: the recoiler, tensioning and unloading.

  • Slit coil inside diameter: it should fit the mandrel of the uncoiler that will run it, for example on your tube mill.
  • Maximum slit coil outside diameter or weight: a narrow slit coil is much lighter than its master coil, but it must still suit the next uncoiler. The recoiler stops when the coils reach the planned diameter. For how a tube mill uncoiler is chosen, see 10 Steps to Specify an ERW Tube Mill: Tube Size to Full Line.
  • Tension: the tensioning device holds every strip back so that each slit coil winds tightly and evenly, and is set up for the thickness range and number of strips you specify.
  • Unloading: the mandrel collapses and the slit coils are pushed off. Tell us how coils leave the line in your plant, for example by crane, forklift or coil car, and whether they must be strapped.

Step 7: output → line speed and setup time

Line speed alone does not tell you output. A slitting line stops to load, thread and unload each master coil, and it stops for every pattern change while the knives and spacers are reset. A plant that runs many short orders spends a large part of each shift on setup; a plant that runs long orders of one pattern spends most of it cutting.

So, besides line speed, tell us your annual tonnage, how many master coils you slit per shift and how many pattern changes you make per day or week.

The FT line speeds are 70 to 100 m/min for strip up to 4 mm, depending on the model, and 30 m/min for heavy-gauge strip up to 8 mm. The speed you can actually run depends on the material and the pattern. When you compare offers, compare speed figures at the same thickness and material.

Step 8: workshop, cranes and power → layout

A slitting line runs offline, ahead of the tube mill or roll-forming line it supplies. Plan floor space for master coil storage, the line itself, slit coil storage and knife and spacer storage. The crane must lift your heaviest master coil. Tell us the workshop size, crane capacity and local supply voltage and frequency. Once the contract takes effect, we provide layout and foundation drawings. When output and slitting patterns allow, one slitting line can supply more than one tube mill.

Common mistakes when specifying a slitting line

  • Specifying by maximum width only: thickness and strength decide the knives, the drive and the speed.
  • Planning heavy-gauge output at the thin-strip speed: on FT1000, FT1250 and FT1600, strip up to 8 mm runs at 30 m/min.
  • Ordering without a pattern list: the line arrives without the knife and spacer sets you need.
  • Forgetting the next machine: slit coil inside diameter and weight must suit the uncoiler that will run them.
  • Leaving out edge trim and setup time: both affect your cost per ton and your real output.
  • Comparing offers with different speed conditions or a different tooling scope.

Slitting line data sheet: what to send

Send as much of the following as you can, and mark anything not yet decided as "to be confirmed":

  • Material: grade, yield and tensile strength, coating
  • Master coils: width range, thickness range, maximum weight, inside and outside diameter, edge condition, width tolerance
  • Slitting patterns: strip widths and number of strips for each pattern; the narrowest strip and its thickness
  • Slit coils: inside diameter, maximum outside diameter or weight, strapping and unloading method
  • Output: annual tonnage, master coils per shift, pattern changes per day or week
  • Plant: workshop size, crane capacity, local supply voltage and frequency, and any electrical brand or standard you require
  • Scope: slitting line alone, or together with a tube mill line

InGen MillTek FT slitting lines

InGen MillTek supplies FT slitting lines for strip widths up to 250, 800, 1,000, 1,250 and 1,600 mm. They slit cold-rolled and hot-rolled carbon steel strip, galvanized strip and ZAM coated strip; stainless and high-strength steel are reviewed for each project. A slitting line can be supplied on its own or together with a tube mill line. The full model table is on our Slitting Lines & Slitters page. Prices are quoted for each configuration.

Frequently asked questions

Prepared by the InGen Engineering Team. Values are reference values and are confirmed in the technical proposal and technical agreement.

  • What is slitting equipment? The machines that cut wide coils into narrower strips: an uncoiler, a feed guide, the slitter, a scrap winder, a tensioning device and a recoiler. Together they form a coil slitting line.
  • Is a metal slitting machine the same as a slitting line? The name is used for both the slitter alone and the whole line. When you compare offers, check which machines each one includes.
  • How do I choose the width of a slitting line? Take your widest master coil. In our FT models, the number is the maximum strip width in millimeters.
  • Can one slitting line cut thin and heavy-gauge strip? Yes, within its range. On FT1000, FT1250 and FT1600 the same machine runs strip up to 4 mm at the higher speed and heavy-gauge strip up to 8 mm at 30 m/min; the knife settings are changed for each thickness.
  • How many strips can I cut at once? That depends on the coil width, the strip widths, the edge trim, the strip thickness and the slitter configuration. Send us your patterns and we will confirm them.
  • Do I need spare knife sets? Knives wear and are reground. A spare set lets you keep slitting while the other set is being reground.
  • What does a coil slitting line cost? It is configured to your coils, patterns and output, and quoted for each configuration.

About this article

Prepared by the InGen Engineering Team. This article explains a selection method; it is not a specification or performance guarantee for any project. The example is an estimate for illustration. Final parameters are set in the technical proposal and technical agreement. For the working principle of a slitter, see What Is a Slitting Line? How a Coil Slitter Works.

Source: JiangSu InGen MillTek Co., Ltd. official website

Further reading

Technical guides

All news & guides